01.½ºÄÉÀÏÆ®·°/¶ôŬ
02.¿¢½Ã¾ó/SCX-10
03.µå¸®ÇÁÆ® ÀÚµ¿Â÷
04.ÀÚµ¿Â÷ Å°Æ®
05.º¸Æ®/ÅÊÅ©/¹ÙÀÌÅ©
06.MINI-Z/¹ö±â
07.¹Ì´ÏÀÚµ¿Â÷
08.ºñÇà±â/µå·Ð/Çï±â
09.Á¶Á¾±â/¼ö½Å±â/¼­º¸
10.Àüµ¿°ü·Ã/¹èÅ͸®
11.¿£Áø/°ü·ÃÁ¦Ç°
12.ºê·£µåº° »óÇ°
13.¹Ùµð/µµ·á/ŸÀ̾î/LED
14.°ø±¸/°ø±¸¹Ú½º/°¡¹æ
15.¿ÀÀÏ/º£¾î¸µ/±¸¸®½º
³ª»ç/³ÊÆ®/ÅϹöŬ/½É
16.ÀÚµ¿Â÷ºÎÇ°/¿É¼Ç
17.ÀÚµ¿Â÷ °ø¿ë/º§Æ®/¼ï
18.Ư°¡»óÇ°
19.¹Ì´Ï4±¸/¿Ï±¸/¹°ÃÑ
20. ÀÚÀ¯/Áß°íÆǸÅ

ºñ¹Ð¹øÈ£ È®ÀÎ ´Ý±â
¿¢½Ã¾óAXIAL ¿¢½Ã¾óAXIAL > SCX-10 I/II ½Ã¸®Áî ½ºÆä¾î/¿É¼Ç > SCX-10 II VANQUISH ¿É¼Ç > VPS01353 Hurtz Dig V2 Red
ÀÌÀü»óÇ° VPS01353 Hurtz Dig V2 Red ´ÙÀ½»óÇ°
   
Á¦Á¶È¸»ç : VANQUISH
ÆǸŰ¡°Ý : 104,000¿ø
Àû¸³±Ý¾× : 1%
¼ö·® EA
 

 
 



Product Description

Vanquish Products Aluminum Hurtz Shifter 3 Position Dig for Axial 3-Gear Transmissions

  • Updated dig unit was designed to increase the capability of your vehicle while maintaining maximum strength
  • Compatible with Axial SCX10, SCX10-II RTR and AX10. May also be used in Wraith by changing the transmission case
  • Rear output is bearing supported for better driveline efficiency and cross drilled to work with thru pin style driveshafts
  • Rear output does not slide in and out, so driveshaft length is easier to manage
  • Servo mount is attached to dig case for simple installation
  • All drive parts are made from high quality and heat treated chromoly steel
  • Total shifter travel needed to shift to all three positions is 0.73 inches, a 24mm servo horn is recommended
  • Servo mount can use most standard size servos*
  • The lever design of the shifter means that you do not need an expensive servo to reliably operate this unit**
  • V2 design works with stock Axial 3-gear transmission cases as well as any Vanquish Products SCX10 transmission housing***

 

* Servo case designs and offsets vary by manufacturer, Futaba, Hitec and Tactic servos have been tested to fit but not every model can be verified

** A radio with an open auxiliary channel and programmable end points is needed to ensure that the dig unit works properly and that your servo will not overheat

*** The Hurtz dig will mount onto any Axial 3 gear transmission case that uses a bolt on metal motor plate.


 
 
 
 
À̸§ :
³»¿ë :
ÆòÁ¡
°í°´Æò°¡ : ÆòÁ¡ ¡Ú¡Ú¡Ú¡Ú¡Ú  
 
 
 
 
»óÇ°¿¡ ´ëÇØ ±Ã±ÝÇÑ Á¡À» ÇØ°áÇØ µå¸³´Ï´Ù.
 
Ȩ